Strapping Tools, Seals and Break Strength: How to Match Them
Share
Pick strapping in this order: the load decides the material, the material decides width and break strength, and the strap decides the tool and seal. Do it backwards and you end up with a tool that doesn't fit your strap.
Material in one paragraph
Poly (PP) is the cheap, light-duty strap for boxes and light bundles; it stretches and slowly loses tension. Polyester (PET) holds tension, gives a little when a load settles, won't rust, and has replaced steel on most pallet, block and lumber loads. Steel has the most strength for its width and almost no stretch, so it's still the call for hot product, sharp-edged metal and coils. Woven cord strap ties off with a wire buckle and needs no power tools. The full material comparison is in Steel vs. Polyester vs. Polypropylene, and When Cord Strapping Wins. This guide picks up after you've chosen the material: break strength, tools and seals.
How much break strength do you need?
The joint is the weak spot. A sealed or welded joint holds less than the strap's rated break strength, and how much less depends on the seal and the tool, so don't size right at the limit.
Rules of thumb:
- Box closing: 1/2 in poly, 300 to 400 lb
- Light pallet unitizing (under 1,000 lb / 450 kg): 1/2 in poly or light PET
- Heavy pallets, block, brick, lumber: 1/2 to 5/8 in PET, 600 to 1,400 lb
- Coils, steel, hot product: steel, sized to the load by your shipper or the receiving spec
Strap keeps snapping? Check for sharp corners (add corner boards), over-tensioning and wrong seal size before you buy heavier.
Width alone doesn't tell you strength. A 1/2 in PET can outpull a 1/2 in poly by double. Pick the break strength first, then the width your tool takes.
Tools: hand vs battery vs machine
- Manual tensioner + sealer (crimper): cheapest setup. Two tools, one seal per joint. Fine for a few dozen straps a day.
- Combination tool: tensions, seals and cuts in one tool. Faster, and fewer lost seals.
- Battery tool (friction weld): no seals at all on PP and PET, so the joint is a weld. Worth it at higher volumes, and easier on wrists.
- Strapping machine (semi-auto or arch): for box lines. Needs machine-grade strap, and the coil core size has to match the machine.
Core size matters. A 16 x 6 core coil won't sit right on an 8 x 8 dispenser. See Strapping Seals and Core Sizes.
Seals and buckles
- Open seals: slide in from the side. The usual seal for manual tools.
- Closed (thread-on) seals: you thread the strap through. Common on some steel tools.
- Push or full-overlap seals: steel, for higher joint strength
- Wire buckles: cord strap only. Match buckle size to strap width.
Match seal width exactly to strap width, and match seal type to the material. A poly seal on PET or steel won't hold.
Quick picks
Browse all: Strapping
- Poly, hand grade: PAC Hand Grade Polypropylene Strapping. 1/2 in, 300 lb, 9,000 ft coil (16 x 6 core), 24-coil minimum.
- Polyester: PAC Polyester Strapping, Embossed. 3/8 in, 425 lb, 12,500 ft coil, 28-coil minimum. Sizes up to 3/4 in, 1,900 lb.
- Steel: PAC Portable Steel Strapping Coils. 3/8 in regular duty, 665 lb, 300 ft coil, 10-coil minimum. 1/2 to 3/4 in sizes are also listed, plus high-tensile.
- Cord strap: PAC Woven Polyester Cord Strapping, Heavy Duty. 1/2 in, 1,280 lb, 3,624 ft coil, 72-coil minimum. Up to 1-1/2 in, 7,700 lb.
- Seals: PAC Plastic Strapping Seals, 1/2 in open seals, case of 1,000. PAC Steel Strapping Seals, 1/2 in regular-duty open seals, case of 1,000.
- Tools and buckles: Seals, Buckles & Tools Matched to Your Strap (quote).
We ship nationwide to all lower 48 US states, from vendor warehouses across the US. Send us your list and we'll quote it: Send Your List.
FAQ
What break strength strapping do I need?
Box closing needs about 300 to 400 lb. Light pallets need 1/2 in poly or light PET. Heavy pallets and yard loads usually run 600 to 1,400 lb PET. Leave margin, because the sealed joint is weaker than the strap.
Do I need seals for strapping?
With manual tensioners and crimpers, yes: one seal per joint, matched to strap width and material. Battery friction-weld tools on poly and PET need no seals. Cord strap uses wire buckles.
What's the difference between hand grade and machine grade poly strap?
Machine grade is made to tighter width and thickness tolerances so it feeds through strapping machines without jamming. Hand grade is for manual tools and dispensers.
What does 16 x 6 or 8 x 8 mean on strapping?
It's the coil's core size, inner diameter by width in inches. It has to match your dispenser or machine.